In a Y-connected circuit, the magnitude of each line current is A. one-third the phase current B. three times the corresponding phase current C. equal to the corresponding phase current D. zero

CoolInterview.com - World's Largest Collection of Interview Questions

Sponsored Links

Interview Questions

Our Services

Get 9,000 Interview Questions & Answers in an eBook.

9500+ Pages
9000 Question & Answers
All Tech. Categories

14 MB Content

Get it now !!

INTERVIEW QUESTIONS ELECTRICAL & ELECTRONICS ENGINEERING(EEE) DETAILS

Question :
In a Y-connected circuit, the magnitude of each line current is
A. one-third the phase current
B. three times the corresponding phase current
C. equal to the corresponding phase current
D. zero

Category Electrical & Electronics Engineering(EEE) Interview Questions

Rating (0.2) By 173 users

Added on 6/17/2011

Views 260

Rate it!

Answers:

Option C

If you have the better answer, then send it to us. We will display your answer after the approval.
Rules to Post Answers in CoolInterview.com:-
There should not be any Spelling Mistakes.

There should not be any Gramatical Errors.

Answers must not contain any bad words.

Answers should not be the repeat of same answer, already approved.

Answer should be complete in itself.

Name :*

Email Id :*

Answer :*

Verification Code Not readable? Load New Code

Enter the above shown code:*

Inform me about updated answers to this question

Related Questions View Answer

In a Y-Y source/load configuration, the
A. phase current, the line current, and the load current are all equal in each phase
B. phase current, the line current, and the load current are 120? out of phase
C. phase current and the line current are in phase, and both are 120? out of phase with the load current
D. line current and the load current are in phase, and both are out of phase with the phase current View Answer

In a -connected source feeding a Y-connected load,
A. each phase voltage equals the difference of the corresponding load voltages
B. each phase voltage equals the corresponding load voltage
C.each phase voltage is one-third the corresponding load voltage
D.each phase voltage is 60? out of phase with the corresponding load voltage View Answer

In a certain three-wire Y-connected generator, the phase voltages are 2 kV. The magnitudes of the line voltages are
A. 2,000 V
B. 6,000 V
C. 666 V
D. 3,464 V View Answer

In a -connected source driving a -connected load, the
A. load voltage and line voltage are one-third the source voltage for a given phase
B. load voltage and line voltage are two-thirds the source voltage for a given phase
C.load voltage and line voltage cancel for a given phase
D. load voltage, line voltage, and source phase voltage are all equal for a given phase View Answer

In a three-phase system, when the loads are perfectly balanced, the neutral current is
A. zero
B. one-third of maximum
C. two-thirds of maximum
D. at maximum View Answer

In a three-phase system, the voltages are separated by
A. 45? B. 90?
C. 120? D. 180? View Answer

The parallel combination of a 470 resistor and a 1.2 k resistor is in series with the parallel combination of three 3 k resistors. A 200 V source is connected across the circuit. The resistor with the most current has a value of
A. 470 or 1.2 k
B. 3 k
C. 470
D. 1.2 k View Answer

A voltage divider consists of two 100 k resistors and a 12 V source. What will the output voltage be if a load resistor of 1 M is connected to the output?
A. 0.57 V
B. 6 V
C. 12 V
D. 5.7 V View Answer

Referring to Problem 14, if a 10 k load is connected to the higher of the two outputs, the loaded voltage value will be
A. 3.48 V
B. 4 V
C. 2 V
D. 4.92 V View Answer

In a certain five-step R/2R ladder network, the smallest resistor value is 1 k. The largest value is
A. indeterminable
B. 2 k
C. 10 k
D. 20 k View Answer

A balanced Wheatstone bridge consists of an RV of 3,500 , an R2 of 200 , and an R3 of 680 . The value of RUNK is
A. 680
B. 1,029
C. 200
D. 880 View Answer

Two 3.3 k resistors are in series and this series combination is in parallel with a 4.7 k resistor. The voltage across one of the 3.3 k resistors is 12 V. The voltage across the 4.7 k resistor is
A. 24 V
B. 12 V
C. 0 V
D. 6 V View Answer

A 6 V battery output is divided down to obtain two output voltages. Three 2.2 k resistors are used to provide the two taps. The two output voltages are
A. 2 V, 4 V
B. 2 V, 2 V
C. 2 V, 6 V
D. 4 V, 6 V View Answer

A 12 k resistor, a 15 k resistor, and a 22 k resistor are in series with two 10 k resistors that are in parallel. The source voltage is 75 V. Current through the 15 k resistor is approximately
A. 14 mA
B. 1.4 mA
C. 5 mA
D. 50 mA View Answer

The parallel combination of a 470 resistor and a 680 resistor is in series with the parallel combination of four 2 k resistors. The total resistance is
A. 1,650
B. 1,078
C. 77.8
D. 778 View Answer

A certain circuit is composed of two parallel resistors. The total resistance is 1,403 . One of the resistors is 2 k. The other resistor value is
A. 1,403
B. 4.7 k
C. 2 k
D. 3,403 View Answer

When a load resistance is removed from the output of a voltage divider circuit, the current drawn from the source
A. decreases
B. increases
C. remains the same
D. is cut off View Answer

The parallel combination of a 6.8 k resistor and a 10 k resistor is in series with the parallel combination of a 2.2 k resistor and a 1 k resistor. A 100 V source is connected across the circuit. The resistor(s) with the greatest voltage drop is (are)
A. 6.8 k
B. 2.2 k
C. 6.8 k and 10 k
D. 2.2 k and 1 k View Answer

The internal resistance of a 30,000 ohm/volt voltmeter set on its 50 V range is
A. 15,000
B. 150,000
C. 1,500,000
D. 15,000,000 View Answer

On which of the following voltage range settings will a voltmeter present the minimum load on a circuit?
A. 1 V
B. 50 V
C. 500 V
D. 1,000 V View Answer

Please Note: We keep on updating better answers to this site. In case you are looking for Jobs, Pls Click Here Vyoms.com - Best Freshers & Experienced Jobs Website.
View ALL Electrical & Electronics Engineering(EEE) Interview Questions